A Tank Tee is 1/4″ compression fitting with multiple connections and accessory plug-ins, when utilized the installation is neat and compact. There are 2 line connections, one for the inlet supply line from the pump / well, the other links to the release line to the plumbing system. 4 FPT item plug-ins for any stress switch, pressure gauge, comfort valve and drain device eliminate the requirement for having several fixtures and nipples which add clutter around a pressure tank.

Kinds of Tank Tees

Tank tees are available in various measures short (3”) to long (16”) to work using the connection sizes and places on different brands of pressure tanks. The 2 major style types are Union and Non-union which may be known as solid or 1-piece tank tees. They come in 1” and 1-¼” with male or female tank connections. Irrespective tank tees are equipped for hooking up for any pre-charged pressure tanks. Tank tee length dimensions are Center-End-Lengths (CEL)

Are used on stress tanks using the tank connection protruding through the side in the tanks base. Short tees range from 3” to 4-1/2” CEL. Short tank tees can be found in several kinds of tank connection as shown listed below.

Long Tees Tank

Are employed on pressure tanks with all the tank link being either at the middle or offset inside the foot of the tanks base. Long tanks tees have male NPT tank connection and are available in a number of measures. For a longer time tank tees are essential as the size from the pressure tank chosen raises, the CEL must be sufficient to increase the tee head out significantly sufficient so that the stress change can threaded on or off without contacting pressure tank. Diagram, technology sketching

Union vs. Low-Union Tank Tees

The benefits of union tank tees are realized during initial installation, and considerably reduces the labor included for tank replacement. A union kind tee easily disconnects the existing tank, which can be removed within minutes departing all of the line and item connections and wiring intact. The new tank can then be installed with the tank tee lower leg from the old tank, set in place and reconnected for the tank tee head by tightening up the union. Job done!

Union tees that include an O-diamond ring provide a reliable watertight seal. No reason to worry about the link leaking. It is recommended to pick an excellent tank tee that utilizes a North American regular O-ring which are plentiful in case a substitute is actually required.

Low-union tank tees carry out the same job, are less cash and save money on the acquisition cost. Nevertheless, they merely do not possess the identical ease of installation and time saving benefits specially when a tank must be changed. The additional work involved throughout set up or tank substitute will far surpass the initial cost savings around the tee.

Stainless Tank Tees

Stainless steel tank tees more cost competitive than No-Lead Bronze and are replacing bronze (red-colored brass) tank tees because the creation of No-Lead requirements in 2014. Usually cast from 304 stainless that is extremely durable and incredibly corrosion proof. Although stainless steel tees are more expensive than brass, they actually do not include zinc relieving the difficulties with dezincification that can happen when utilizing brass alloy tank tees in aggressive water conditions. Another advantage will be the very high strength of stainless practically eliminates all probability of stress cracking when threading into female connections.

Brass Alloy Tank Tees

Brass tank tees are less costly and they are best for installations in most locations. Nevertheless brass alloys2-07TK-25SF-2NL are certainly not as rust resistant as stainless steel, consequently installations in places that the water is extremely corrosive to brass, it is suggested to update to stainless-steel.

Galvanized Tank Tees

Galvanized tees are less costly than each stainless steel and brass tank tees. Their use is typically07HC125G limited to installations on galvanized stress tanks without having a bladder. Galvanized tees are selected to remove the chance of galvanic rust between different metals. Galvanized tank tees used in conjunction with galvanized nipple and fixtures lgotli the situation. It is essential to note that some plumbing rules do not let using galvanized fixtures and nipples, one must verify that galvanized tank tees meet all the relevant plumbing program code specifications.

Pvc material Tank Tees

Pvc material tank tees certainly are a really aggressive option compared to stainless steel, brass, and07PT-25-2 galvanized components. They are very resistant against corrosion, they may not as durable as steel tank tees, neither are available many configurations available. They may be considered a really suitable alternative, when proper Pvc material installation methods are implemented, the use of a high-quality line sealant paste rather than PTFE thread sealant tape and avoiding over tightening will reduce the chance of more than worrying the feminine NPT accessory ports.

1 2 Inch Compression Fitting..